Kobelco excavator parts specialist since 2007 — Guangzhou, China WhatsApp / WeChat: +86 181 4482 5432 · Tel: +86 20-32036036 · kobelco-parts@foxmail.com
Blog

D04EG Leaks and Overheating: Head Gasket, Front Seal, Pulley and Water Pump

Oil at the front of a D04EG and a rising temperature gauge on a Kobelco SK135SR or SK140 are usually connected stories. Guangzhou Shenyue Machinery Technology Co., Ltd. maps the leaks to the parts: VA32K0102501, VA32A1104010, VA32B2011201, VA32K4500010.

Blog / D04EG Leaks and Overheating: Head Gasket, Fr…
November 8, 2026 · Shenyue Kobelco Parts Team
D04EG updated cylinder head gasket VA32K0102501 from stock
The updated cylinder head gasket VA32K0102501 from our shelf. On the D04EG, coolant loss, oil misting and overheating often share one chain of causes across these four components.

On the D04EG — the four-cylinder turbocharged common-rail diesel in Kobelco's SK135SR-3 and SK140SRLC short-radius machines — owners often treat each leak as its own small problem: a mist of oil at the crankshaft front, a weep at the water pump, a temperature gauge that climbs on hot afternoons. In practice these symptoms form one connected story, and reading them together is what separates a planned Saturday repair from an overheated engine and a cylinder head job. Guangzhou Shenyue Machinery Technology Co., Ltd. stocks the four components at the heart of this story — the updated head gasket VA32K0102501, the crankshaft front oil seal VA32A1104010, the crankshaft pulley VA32B2011201 and the water pump VA32K4500010 — and this guide maps the symptoms to the parts.

The water pump is the first suspect

An overheating D04EG with a falling coolant level and no obvious hose leak should have its water pump checked before anything more dramatic is condemned. The pump VA32K4500010 announces its wear through the weep hole, through a rough bearing growl at idle, or through play in the pulley shaft. A pump moving less coolant than it should produces exactly the pattern owners describe: fine on light work, creeping temperature under sustained load, worst in hot weather. Replacing the pump on time is cheap insurance; letting it run until the bearing fails risks the fan drive and everything the belt touches.

Front oil seal and pulley: one job, two parts

Oil misted across the front of the engine and thrown by the fan is the classic sign of the crankshaft front oil seal VA32A1104010 reaching the end of its life. The seal runs against the crankshaft pulley VA32B2011201, and here is the detail that decides whether the repair lasts: a pulley whose sealing surface is worn or grooved destroys a new seal in short order. Inspect the pulley surface whenever the seal comes out, and replace both together when wear shows; the counterface and lip requirements behind that rule are set out in general terms in SKF's published sealing guidance. The pulley also carries the belt drive, so cracking or wobble there is its own reason for replacement. Torque figures and the seal-fitting procedure belong to the service manual for the machine serial.

An oil leak at the front of the engine is never only an oil leak on a working excavator. Misted oil coats the radiator and oil cooler fins, dust sticks to the film, and the cooling stack quietly loses capacity. The overheating that follows is blamed on the radiator when the root cause was a twenty-dollar seal.

The head gasket: when the small leaks were warnings

The updated cylinder head gasket VA32K0102501 enters the story when the earlier signs were missed or when the engine has genuinely overheated. The symptoms split by failure mode: combustion gas into the coolant shows as bubbling and pressure in the radiator and unexplained coolant loss; coolant into the oil shows as emulsion on the dipstick and filler cap; an external path shows as oil or coolant tracking down the block. A compression or leak-down test per the service manual, plus a check for combustion gas in the coolant, settles the diagnosis before the head comes off. Note also the exhaust manifold nut VA32A3202300 while planning the job — on these engines the manifold fasteners live at high temperature and commonly seize, so fresh nuts belong on the same order as the gasket set.

What you seeComponent to checkPart reference
Temperature creeps under loadWater pumpVA32K4500010
Oil mist at engine frontFront oil seal + pulley surfaceVA32A1104010 / VA32B2011201
Coolant loss, radiator bubblingHead gasketVA32K0102501
Emulsion on dipstickHead gasket, oil coolerVA32K0102501
Seized manifold fastenersExhaust manifold nutsVA32A3202300

Ordering the repair set

These repairs reward ordering as a set: seal and pulley together, gasket with manifold nuts and the head bolts the manual calls for, pump with a coolant change. Send the machine model, the serial number and the numbers from the parts being replaced, and say whether the history includes an overheat, because it changes what else should be checked. We are an independent supplier, not a Kobelco dealer; we hold these Mitsubishi D04EG references, sourced through authorized Mitsubishi Heavy Industries channels, among 3,000+ part types on the shelf, with 100,000+ part numbers available to order, and we confirm every fitment against the serial. See the individual listings — head gasket VA32K0102501, front oil seal VA32A1104010, crankshaft pulley VA32B2011201 and water pump VA32K4500010 — and the machine context in our short-radius parts guide. Buyers cross-referencing these numbers across brands can also check listings on corbayparts.com, our international export site, and enquiries reach us through the contact page.

Frequently Asked Questions

Why does my SK140 with the D04EG overheat only under load?

A weakening water pump is the first suspect — it moves enough coolant for light work but not for sustained load. Check the weep hole, bearing noise and shaft play on pump VA32K4500010. Guangzhou Shenyue Machinery Technology Co., Ltd. stocks the replacement and confirms fitment against the machine serial.

Should the crankshaft pulley be replaced with the front oil seal on a D04EG?

Inspect it every time. A worn or grooved sealing surface on pulley VA32B2011201 destroys a new seal VA32A1104010 quickly, so the two are often replaced together. Guangzhou Shenyue Machinery Technology Co., Ltd. supplies both references from stock.

What are the signs of a failing D04EG head gasket?

Bubbling or pressure in the radiator, unexplained coolant loss, emulsion on the dipstick, or oil and coolant tracking down the block. The updated gasket is VA32K0102501. We recommend a leak-down test per the service manual before teardown.

Are there related parts to order with the D04EG head gasket VA32K0102501?

Yes — the exhaust manifold nut VA32A3202300 commonly seizes from heat and should be renewed with the gasket job, along with any head bolts the service manual specifies. Guangzhou Shenyue Machinery Technology Co., Ltd. quotes the set against the machine serial.

Need the parts this article talks about?

Send your part numbers and a photo of the nameplate — real photos and pricing come back with the quote.

Start an Inquiry