Every workshop eventually owns a machine that will not be repaired: a rolled excavator with a sound engine, a high-hour unit with a failed swing gearbox, or a machine whose undercarriage is worth more than the hull. The question is whether to sell it as a non-runner, repair it, or part it out. Parting out can return more, but only if the machine has the right components, the storage to hold them, and the paperwork to sell them credibly. This guide from Guangzhou Shenyue Machinery Technology Co., Ltd. sets out the decision and the practical sequence.
The decision, in numbers you can check
Start with three figures: the value of the machine as a non-runner, the realistic total of its saleable assemblies, and the cost of removal, storage and selling. The second figure is almost always higher on paper and lower in practice, because some parts never sell and some sell only after a year on the shelf. Weight the total by demand: a travel motor, a hydraulic pump, a swing motor, a controller and a cylinder sell; brackets, panels and hoses usually do not. If the machine is complete and starts, selling it as a working unit is normally the better outcome. Parting out wins when the structure is damaged but the powertrain and hydraulics are sound.
Which assemblies hold value
The core list is predictable. Final drives and travel motors: GM38VB on the SK200-8 and SK210-8, GM38VC on the SK200-10 generation, which do not interchange. Swing motors: M5X130 class on the 20-tonne machines, M5X180 class with reference LC15V00022F1 on the SK330-8 class and above. Hydraulic pumps: K3V112DT on the SK200-8, with K5V140 belonging to the SK350-8 and SK330-8 class. Engines: the Hino J05E family, plus the Mitsubishi D04EG in the short-tail models. Controllers, monitors, cylinders, valves and complete undercarriages follow.
| Assembly | Why buyers want it | What to record before removal |
|---|---|---|
| Travel motor / final drive | High failure rate, high replacement cost | Model, serial, oil condition, test result |
| Swing motor and gearbox | Wear item on high-hour machines | Backlash, noise, leak history |
| Hydraulic pump | Core of the machine's working ability | Pressure and flow test before removal |
| Engine and controller | Expensive to replace new | Hours, smoke, compression, software label |
Removal order and testing
Test before you remove. A pump that produced good pressure and flow on the machine is worth several times a pump of unknown condition, and the test takes an hour. Photograph the machine as a whole before dismantling, then photograph each assembly in place with its plate readable. Remove in an order that keeps the machine stable: attachment first, then the upper structure components, then the engine and pump, and leave the undercarriage until the machine is blocked securely. Cap every port and hose the moment it is opened, and bag and label the fasteners with the part they came from.
Storage, tagging and presentation
Store assemblies upright and dry, with ports capped and shafts protected. A travel motor left on its side in the mud loses value faster than one on a pallet under cover. Keep controllers and monitors indoors, because heat and damp kill electronics that were working when removed. Photograph each item on a clean background, list the reference and condition, and be honest about the reason for dismantling: buyers accept a donor part from a rolled machine, but not a part described as tested when it was never run.
Compliance and the things that bite
Draining fluids is the first environmental obligation: engine oil, hydraulic oil, coolant and fuel all need proper collection, and the refrigerant in the air-conditioning system must be recovered rather than vented. Batteries are separate waste. If the machine is sold as a whole non-runner instead, the same fluids travel with it, so drain before transport. Keep the machine's registration or import documents with the parts records where local rules require them, and never sell a component with a defaced or removed identification plate.
Selling the parts
Price by condition class, not by hope: new genuine, used serviceable, repairable core. Our guide to used and salvage parts grading explains how the three classes are judged, and the core exchange guide explains what a rebuilder will pay for a rebuildable unit. List the assemblies that carry references — for example the GM38VB travel motor — with the number in the title, because buyers search by number rather than by description. Guangzhou Shenyue Machinery Technology Co., Ltd. buys and grades cores, and often advises owners to sell the whole machine rather than dismantle it when the numbers do not justify the work. Sellers moving volume across several brands also list on corbayparts.com; Kobelco's corporate site at kobelco.co.jp helps confirm the original model range.
Frequently Asked Questions
How do I decide whether to part out a Kobelco?
Compare the value as a non-runner, the realistic total of saleable assemblies, and the cost of removal, storage and selling. Parting out usually wins when the structure is damaged but the powertrain and hydraulics are sound. If the machine is complete and starts, selling it whole is normally better. Guangzhou Shenyue Machinery Technology Co., Ltd. grades cores and can advise.
Which Kobelco components are worth removing first?
Travel motors and final drives, swing motors, hydraulic pumps, engines, controllers and cylinders. On an SK200-8 the travel motor is GM38VB and the pump is K3V112DT; on the SK200-10 the travel motor is GM38VC and does not interchange. Test each assembly before removal and photograph its plate.
How should used Kobelco parts be stored?
Upright, dry and capped. Travel motors and pumps should sit on pallets with ports sealed and shafts protected, and controllers should stay indoors away from heat and damp. Tag every item with the machine serial, component number, hours, test result and a photo of its plate so buyers can judge condition.
What has to be drained before dismantling an excavator?
Engine oil, hydraulic oil, coolant and fuel must be collected properly, the air-conditioning refrigerant must be recovered rather than vented, and batteries are handled as separate waste. Guangzhou Shenyue Machinery Technology Co., Ltd. treats fluid recovery and clear identification as part of the grading process, not an afterthought.