Kobelco SK200-10 · 2.4M Arm Hydraulic Piping (Crusher & Breaker) · 10 part numbers
No illustration for this section
The 2.4M Arm Hydraulic Piping (Crusher & Breaker) is listed without an exploded view in the SK200-10 catalogue — the parts table below is the authoritative reference, and every part number is confirmed against your machine serial before we quote.
The 2.4M Arm Hydraulic Piping (Crusher & Breaker) group on the Kobelco SK200-10 contains 10 separately orderable part numbers. The Ref. column mirrors the callout numbers on the illustration, so a part can be ordered straight from the drawing. All numbers are taken from the machine's own parts catalogue — nothing here is generic.
| Ref. | Part No. | Description | Qty / Assy |
|---|---|---|---|
| YN43H00414F1 | HYD LINES, ARM 2.4M | ||
| 1 | ZX60U12135 | HOSE ASSY | 1 |
| 2 | YN43H01576D9 | HOSE | 1 |
| 3 | ZE13X12000 | CLAMP, HALF | 2 |
| 4 | ZE13X16000 | CLAMP, HALF | 2 |
| 5 | HM83C10035G1 | SEMS BOLT - | 4 |
| 6 | HM83C12045G1 | SEMS BOLT - | 4 |
| 6 | HM83C12040G1 | SEMS BOLT - | 4 |
| 7 | ZD12P02600 | O RING - | 1 |
| 8 | ZD12P03400 | O RING - | 1 |
Part numbers as fitted to the Kobelco SK200-10 excavator. Where a position changed during the production run, the serial number settles which one applies to your machine.
Structurally, these 10 numbers fall into 5 Kobelco number series — HM83C, YN43H, ZE13X among the largest. The list is weighted toward repeated items such as sems, bolt, hose and 3 hardware positions.
The high-quantity positions are: HM83C10035G1 (sems bolt -, ×4 per assembly); HM83C12045G1 (sems bolt -, ×4 per assembly); HM83C12040G1 (sems bolt -, ×4 per assembly). The full list follows below.
Swing, travel and implement circuits share the same pump flow on the Kobelco SK200-10, which is why a fault in one function can point back to a component listed in this group. A pressure test narrows the circuit down; the drawing then narrows it to a part number.
Working from the exploded view is the fastest way to order. Find the component on the drawing, note its callout number, and take the matching reference from the table — that mapping removes the guesswork that comes with describing a part over the phone or in an email.
Usually yes — the callout numbers on the drawing map directly to the Ref. column in the table. If your machine differs by serial range, send a photo of the part and we will confirm before quoting. If that matches your case, quote HM83C10035G1 and we will take it from there.
Yes — send the serial and the part number together; where a position changed across the run we flag it and quote the number that matches your build.
Yes. Send the Kobelco SK200-10 serial number with the part number and we confirm the fit from the serial range. Where a component changed during the production run, we flag it before you commit.
Hydraulic Oil Tank Mounting
View Parts ListSwing Motor Mounting
View Parts ListValve Mounting (Emergency Lowering Valve)
View Parts ListValve Mounting (Boom Emergency Lowering Valve)
View Parts ListFilter List
View Parts ListNut Part Numbers
View Parts ListBushing Part Numbers
View Parts ListPaint Colors
View Parts ListKobelco SK200-10 workshop guide
Read the guideKobelco SK200-10 workshop guide
Read the guideKobelco SK200-10 workshop guide
Read the guideRepair guides written from our own workshop notes on the Kobelco SK200-10 — the same components listed on this page, with the failure patterns and part numbers we see most often from trade customers.