Kobelco SK260LC-12M · Cylinder Hydraulic Piping (Bucket Cylinder) · 14 part numbers
No illustration for this section
The Cylinder Hydraulic Piping (Bucket Cylinder) is listed without an exploded view in the SK260LC-12M catalogue — the parts table below is the authoritative reference, and every part number is confirmed against your machine serial before we quote.
14 separately orderable part numbers make up the Cylinder Hydraulic Piping (Bucket Cylinder) on the Kobelco SK260LC-12M. Take the callout number from the drawing and match it in the Ref. column below. Every entry is a genuine Kobelco part number, confirmed against the serial range before we quote.
| Ref. | Part No. | Description | Qty / Assy |
|---|---|---|---|
| LB43H00096F1 | HYD LINES, CYLINDER | ||
| 1 | LB43H01038P1 | TUBE | 1 |
| 2 | LB43H01181P1 | BAND | 1 |
| 3 | YY42H01924P1 | BAND | 1 |
| 4 | YN43H01097P1 | CLAMP | 1 |
| 5 | ZG91S04000 | NIPPLE, GREASE | 1 |
| 6 | ZG91V02000 | NIPPLE, GREASE | 1 |
| 7 | ZD12P02600 | O RING - | 1 |
| 8 | ZD12A01800 | O RING - | 1 |
| 9 | ZS18C10035 | CAPSCREW | 2 |
| 10 | ZS18C10055 | CAPSCREW | 1 |
| 11 | ZS28C10030 | CAPSCREW | 4 |
| 12 | ZW26X10000 | LOCK WASHER | 2 |
| 13 | ZW16H10000 | WASHER | 1 |
Part numbers as fitted to the Kobelco SK260LC-12M excavator. Where a position changed during the production run, the serial number settles which one applies to your machine.
Read as a dataset, the 14 part numbers spread across 11 number series (LB43H, ZS18C, YY42H being the biggest) The list is weighted toward repeated items such as capscrew, band, nipple and 5 hardware positions.
The high-quantity positions are: ZS28C10030 (capscrew, ×4 per assembly); ZS18C10035 (capscrew, ×2 per assembly); ZW26X10000 (lock washer, ×2 per assembly). The full list follows below.
For workshops planning a full hydraulic health check, the practical sequence is seals first, then wear items such as valve plates and bushings, and only then complete assemblies. The table below supports that sequence because every level of the breakdown is separately orderable.
Rebuild-at-component-level is the practical route for most Kobelco SK260LC-12M hydraulic assemblies. Wear shows up at predictable points — spool clearances, valve plates, bearing sets, seal packages — and those items are listed individually, so you can quote only what is worn instead of exchanging the complete unit.
It is the quantity fitted per assembly in the catalogue — useful when a job calls for more than one of the same part, such as O-rings fitted in a pack. If that matches your case, quote ZS28C10030 and we will take it from there.
Both. Every quotation states the condition of each item — genuine through original supply channels, or a quality OEM alternative — so the choice is yours and it is documented.
We quote new components from this table — genuine or OEM by declaration — rather than exchange units, so you know exactly what is being fitted.
Fuel Tank Mounting (Fuel Pump Mounting, Dust Cover, Remote Drain)
View Parts ListHydraulic Oil Tank Mounting (Right-View Camera)
View Parts ListPto Assembly (Without Hydraulic Pto)
View Parts ListSwing Motor Mounting (Sk280)
View Parts ListFilter List
View Parts ListUndercarriage Parts List
View Parts ListNut Part Numbers
View Parts ListBushing Part Numbers
View Parts ListKobelco SK260LC-12M workshop guide
Read the guideKobelco SK260LC-12M workshop guide
Read the guideKobelco SK260LC-12M workshop guide
Read the guideRepair guides written from our own workshop notes on the Kobelco SK260LC-12M — the same components listed on this page, with the failure patterns and part numbers we see most often from trade customers.