Kobelco SK330-8 · Hyd Lines,Boom 6.5M (21Ft 4In) · 58 part numbers

Illustration reproduced from the Kobelco SK330-8 parts catalogue for part identification only. Callout numbers on the drawing match the Ref. column in the table below. Kobelco is a trademark of its respective owner; Shenyue Machinery is an independent supplier of excavator parts.
58 separately orderable part numbers make up the Hyd Lines,Boom 6.5M (21Ft 4In) on the Kobelco SK330-8. Take the callout number from the drawing and match it in the Ref. column below. The list comes straight from the Kobelco SK330-8 catalogue for this machine family.
| Ref. | Part No. | Description | Qty / Assy |
|---|---|---|---|
| LC42H00175F1 | HYD LINES,BOOM | ||
| LC42H00155F1 | HYD LINES,BOOM | ||
| A1 | LC42H01888P1 | TUBE | 1 |
| A2 | LC42H01889P1 | TUBE | 1 |
| A3 | LC42H01902P1 | TUBE | 1 |
| A4 | LC42H01891P1 | TUBE | 1 |
| A5 | LC42H01806P1 | TUBE | 1 |
| A6 | LC42H01733P1 | TUBE | 1 |
| A7 | YN42H02357P1 | CLAMP | 4 |
| A8 | YN42H02359P1 | CLAMP | 4 |
| A9 | YN42H02348P1 | CLAMP | 2 |
| A10 | YN42H02353P1 | CLAMP | 4 |
| A11 | YN42H02351P1 | CLAMP | 2 |
| A12 | YN42H02321P1 | BUSHING | 3 |
| A13 | YN43H01524P1 | BUSHING | 6 |
| A14 | YY42H01313P1 | O-RING | 2 |
| A15 | ZD12A02100 | O-RING | 6 |
| A16 | ZM73C12035 | SEMS-BOLT | 16 |
| A17 | YN42H02361P1 | CLAMP | 2 |
| LC42H00153F1 | HYD LINES,BOOM | ||
| B3 | PV02B01073D3 | CAP | 16 |
| LC42H00181F1 | HYD LINES,CYLINDER | ||
| LC42H00161F1 | HYD LINES,CYLINDER | ||
| C1 | LC42H01745P1 | TUBE | 1 |
| C2 | LC42H01779D1 | HOSE | 4 |
| C3 | LC42H01802P1 | BAND | 2 |
| C4 | LC42H01750P1 | BAND | 2 |
| C5 | 2432T5986 | CLAMP | 4 |
| C6 | ZE12X16000 | CLAMP,HALF | 8 |
| C7 | ZH22Z04000 | CONNECTOR | 2 |
| C8 | ZG91S02000 | NIPPLE,GREASE | 2 |
| C9 | ZD12P03400 | O-RING | 5 |
| C10 | ZS18C10035 | CAPSCREW | 4 |
| C11 | ZS28C10035 | CAPSCREW | 16 |
| C12 | ZS18C14075 | CAPSCREW | 2 |
| C13 | ZS28C12040 | CAPSCREW | 4 |
| C14 | ZW26X10000 | LOCK WASHER | 4 |
| C16 | ZW16H14000 | WASHER | 2 |
| C17 | ZW26K10000 | WASHER | 16 |
| LC42H00182F1 | HYD LINES,CYLINDER | ||
| D1 | LC42H01746P1 | TUBE | 1 |
| LC42H00183F1 | HYD LINES,CYLINDER | ||
| E1 | LC42H01765P1 | TUBE | 1 |
| E2 | LC42H01766P1 | TUBE | 1 |
| LC42H00184F1 | HYD LINES,CYLINDER | ||
| LC42H00163F1 | HYD LINES,CYLINDER | ||
| F1 | ZX20H16120 | HOSE | 1 |
| F2 | LC42H01873D1 | HOSE | 1 |
| F3 | LC42H01884P1 | BAND | 1 |
| F4 | LC42H01885P1 | BAND | 1 |
| F7 | ZG91V02000 | NIPPLE,GREASE | 1 |
| F8 | ZE13X20001 | CLAMP,HALF | 4 |
| F9 | ZD12P03800 | O-RING | 2 |
| F11 | ZS18C10030 | CAPSCREW | 2 |
| F12 | ZS28C14050 | CAPSCREW | 8 |
| F14 | ZW26K14000 | WASHER | 8 |
| LC42H00185F1 | HYD LINES,CYLINDER | ||
| G1 | LC42H01753P1 | TUBE | 1 |
Part numbers as fitted to the Kobelco SK330-8 excavator. Where a position changed during the production run, the serial number settles which one applies to your machine.
Read as a dataset, the 58 part numbers spread across 20 number series (LC42H, YN42H, ZS18C being the biggest) Expect repeated items such as tube, hyd, lines and 11 hardware positions when you work through it.
The high-quantity positions are: ZM73C12035 (sems-bolt, ×16 per assembly); PV02B01073D3 (cap, ×16 per assembly); ZS28C10035 (capscrew, ×16 per assembly). The full list follows below.
For workshops planning a full hydraulic health check, the practical sequence is seals first, then wear items such as valve plates and bushings, and only then complete assemblies. The table below supports that sequence because every level of the breakdown is separately orderable.
Rebuild-at-component-level is the practical route for most Kobelco SK330-8 hydraulic assemblies. Wear shows up at predictable points — spool clearances, valve plates, bearing sets, seal packages — and those items are listed individually, so you can quote only what is worn instead of exchanging the complete unit.
It is the quantity fitted per assembly in the catalogue — useful when a job calls for more than one of the same part, such as O-rings fitted in a pack. If that matches your case, quote ZM73C12035 and we will take it from there.
Both. Every quotation states the condition of each item — genuine through original supply channels, or a quality OEM alternative — so the choice is yours and it is documented.
We quote new components from this table — genuine or OEM by declaration — rather than exchange units, so you know exactly what is being fitted.
Tank Instal,Hyd
View Parts ListMotor Instal,Swing
View Parts ListHyd Lines,Pump (Suction,Delivery)
View Parts ListHyd Lines,Upp (Main)
View Parts ListFilter List
View Parts ListFrame Assy,Upp
View Parts ListCounterweight Instal
View Parts ListEngine Assy
View Parts ListKobelco SK330-8 workshop guide
Read the guideKobelco SK330-8 workshop guide
Read the guideKobelco workshop guide
Read the guideRepair guides written from our own workshop notes on the Kobelco SK330-8 — the same components listed on this page, with the failure patterns and part numbers we see most often from trade customers.