Kobelco excavator parts specialist since 2007 — Guangzhou, China WhatsApp / WeChat: +86 181 4482 5432 · Tel: +86 20-32036036 · kobelco-parts@foxmail.com
Blog

Kobelco Auto Warm-Up: What the Function Does and the Parts Behind It

Auto warm-up raises idle speed on a cold start so the machine warms its oil before work begins. Guangzhou Shenyue Machinery Technology Co., Ltd. covers the function and the parts that run it.

Blog / Kobelco Auto Warm-Up: What the Function Does…
November 18, 2026 · Shenyue Kobelco Parts Team
Water temperature sensor pair recorded under YN52S00077F1 and YT52S00001P1
Water temperature sensors recorded under YN52S00077F1 and YT52S00001P1. The warm-up function trusts one small sensor to decide when a machine is ready to work.

On a cold morning a Kobelco that starts normally and then refuses to work properly is not broken — it is protecting itself. The auto warm-up function raises engine idle speed when the machine is cold and holds it there until the oil is warm enough to circulate and lubricate properly, then hands control back to the operator without any switch being touched. Guangzhou Shenyue Machinery Technology Co., Ltd. supplies the sensors and actuators behind this function, and the questions we get are almost always the same three: why did it stop engaging, what parts decide it, and can the operator skip it.

What the function actually does

Hydraulic oil behaves like honey when cold. Pumped at full load, it filters badly, lubricates worse and cavitates more easily, which is why a machine worked hard from a stone-cold start pays in pump and seal life within the first half hour. Auto warm-up answers this: on cold start the engine is held at raised idle — faster than low idle, well below work speed — while the system warms. As coolant and oil temperatures climb, the function steps the speed down and releases the machine to normal operation.

The function is automatic by design. There is no switch to hold, which is also why its failures are silent: nothing announces that warm-up stopped engaging, and the first sign is a machine that feels sluggish and noisy through the first working hour, burning fuel without earning.

The parts that decide when the machine is warm

RoleNumbers in our recordsNote
Water temperature sensorYN52S00077F1 / YT52S00001P1Recorded as a related pair
Water temperature sensorVA32G9000201Hino-sourced engine family
Water temperature sensorVA32K9000200Recorded separately — model-specific
Water temperature sensor2489U268F1Recorded number, engine side
Water temperature sensorVHS834201250Recorded with its variant
Throttle step motorYN20S00002F1Executes the speed change

Two patterns hide in that table. First, temperature sensors are model-specific: VA32G and VA32K numbers do not cross, and a sensor that reads at all is not a sensor that reads correctly — a drifting sensor can hold a machine in warm-up for half an hour or skip warm-up entirely, and either outcome costs fuel or pump life. Second, the step motor is the actuator: if the engine will not leave low idle, or will not come down after warming, the motor and its feedback are on the suspect list alongside the sensor.

Symptoms and the order to check them

When warm-up stops engaging, check in this order: read the displayed coolant temperature against a thermometer on a genuinely cold start — a large gap condemns the sensor; then watch whether engine speed responds when the system commands warm-up, which isolates the step motor; then check the connections and harness, because a corroded connector produces exactly the same symptom as a dead sensor and costs nothing to clean. Only after those steps does a controller become the suspect, and by then the evidence is usually clear.

How Guangzhou Shenyue Machinery Technology Co., Ltd. quotes warm-up parts: by machine model and serial, every time. Sensor numbers do not cross between engine families, and two visually identical sensors can read on different scales. We quote against records and say plainly when the sensor we hold is the recorded pair rather than a universal substitute.

Warm-up is not preheat

Cold climates add a second layer that is easy to confuse with this one. Preheat — glow plugs and intake heaters — helps the engine start; warm-up protects the machine after it has started. Machines in genuinely cold regions use both, and the starting side has its own article on our blog. If a machine starts reluctantly, work the preheat chain; if it starts well and works badly, work warm-up.

Kobelco's corporate site remains the reference for function descriptions by generation, and our temperature and speed sensor guide maps the sensing family in depth. For the actuator side, the step motor diagnosis guide covers the failure patterns we see most, and the relay and switching parts sit behind both functions. Sensor numbers for a specific machine can be confirmed by Guangzhou Shenyue Machinery Technology Co., Ltd. through the contact page — send the model and serial and we will match the sensor to the record rather than to a photograph.

Frequently Asked Questions

What does the auto warm-up function do on a Kobelco excavator?

It holds the engine at raised idle after a cold start until coolant and hydraulic oil reach working temperature, then hands control back to the operator. Guangzhou Shenyue Machinery Technology Co., Ltd. sees this as the cheapest protection the machine has: it prevents cold, thick oil from being pumped at full load.

Why did auto warm-up stop engaging on my machine?

Most often the coolant temperature sensor has drifted, so the controller believes the machine is already warm. Compare the displayed temperature with a thermometer on a cold start, then check the step motor response and the connectors before suspecting any controller.

Can I skip warm-up and start working immediately?

You can, but you are spending pump and seal life to save ten minutes. Cold oil filters badly and cavitates more easily, and the damage is cumulative rather than visible on the day. Warm-up is automatic precisely because operators are tempted to skip it.

Which sensor number does my machine need for warm-up?

The model and serial decide it. Our records carry YN52S00077F1 with YT52S00001P1 as a related pair, and VA32G9000201, VA32K9000200, 2489U268F1 and VHS834201250 in different engine families — the numbers do not cross. Guangzhou Shenyue Machinery Technology Co., Ltd. confirms against the serial before quoting.

Need the parts this article talks about?

Send your part numbers and a photo of the nameplate — real photos and pricing come back with the quote.

Start an Inquiry