Kobelco excavator parts specialist since 2007 — Guangzhou, China WhatsApp / WeChat: +86 181 4482 5432 · Tel: +86 20-32036036 · kobelco-parts@foxmail.com
Blog

Kobelco Power Boost: Why the Machine Gets Stronger for a Few Seconds

Power boost is the short burst of extra force on a Kobelco, not a fault. Guangzhou Shenyue Machinery Technology Co., Ltd. explains how boost works, how it fails and which parts sit behind it.

Blog / Kobelco Power Boost: Why the Machine Gets St…
November 7, 2026 · Shenyue Kobelco Parts Team
Kobelco valve YN22V00002F1 from the main relief family
A valve from the main-relief family on our shelf. Boost works by lifting the pressure ceiling these valves set, so relief condition and boost symptoms overlap and must be told apart.

Every Kobelco operator has felt power boost without necessarily naming it: the machine digs into a hard face, holds a heavy load or climbs out of a hole with noticeably more force for a few seconds, then settles back to normal. That burst is by design, not a fault, and it has a parts story of its own. Guangzhou Shenyue Machinery Technology Co., Ltd. supplies the regulators, relief valves and solenoids behind the boost function, and this guide explains what boost does, where the extra force comes from and why the common failure modes are electrical before they are mechanical.

What boost does

Boost is also where the generations differ most. Some builds trigger it automatically on combined movements, others wait for a held switch, and operators occasionally assume the machine has lost boost because they never touch the switch at all. Before condemning parts, read the function as the manual describes it for the serial and try the command deliberately on level ground with a known load, so the test shows what the machine can still do rather than what it did last month. Under normal working, the hydraulic system is limited by its relief setting, which protects the pump and the structure. Boost temporarily raises that ceiling so the machine can break out a loaded bucket, lift against gravity or push the undercarriage up a slope, and it is deliberately limited in duration so the extra duty does not cook the oil or unload the pump continuously. Depending on the model and generation the burst is commanded by a switch the operator holds or triggered automatically during combined movements such as lifting while traveling. Either way the extra force comes from pressure, not from the engine growing stronger.

Where the extra pressure comes from

The boost command acts on the pump regulators and the relief path. On the SK200-8 class the main pump is the K3V112DT, and its regulator assembly 29070821-4927, also quoted as YN10V01006F2, is the part that translates the boost command into increased pump output; the SK330-8 and SK350-8 class runs the larger K5V140, and the two pump families are not interchangeable across classes. The relief valves set the ceiling that boost lifts: our records quote main relief valves V9510318049-T with LP22V00001F1 and YN22V00004F1, and YN22V00001F4 with LC22V00011F1 and V9701310053-T, alongside solenoid valves such as YN22V00035F1 in the command path. The parts book for the serial is the authority on which combination a machine carries.

Never restore "lost boost" by screwing a relief valve in. Settings belong to the service manual for the serial, and they are set with gauges at the test ports. An over-set relief turns every function into a boost cycle and quietly overheats the oil.

How boost fails and how to test it

A machine whose boost has stopped reads as "weak breakout" or "will not hold a grade" while every other function still works, which is the signature that separates boost faults from a tired pump. Start electrical: the boost solenoid coil, its connector and the command path fail first, and a coil that no longer energises explains most cases. Then measure: connect gauges at the test ports and compare the pressures against the manual; our guide to test ports and pressure testing shows the method, and our walkthrough of relief valves and safety circuits covers the valve side. A regulator that does not respond, or a relief that will not hold its setting, is condemned last and replaced with the correct reference.

What you seeMost likely causeFirst check
Never feels stronger, everBoost command pathSolenoid coil and connector
Boost lasts too long or overheatsCommand stuck onSolenoid and switch circuit
Weak everywhere, all the timeRelief or pumpGauge readings vs manual
Strong but oil heats fastRelief over-setSettings vs manual

Ordering the parts

When ordering, state the model and serial, and say whether the machine lost boost suddenly or faded over months, because the two histories point at different parts. Guangzhou Shenyue Machinery Technology Co., Ltd. marks every item genuine, OEM or aftermarket at quotation and checks regulator, relief and solenoid references against the serial before quoting. Hydraulic-components buyers can browse our hydraulic components pages and confirm references on the part-number search page. The K3V and K5V pump families behind these systems are Kawasaki designs, documented at khi.co.jp.

Frequently Asked Questions

Is it normal for a Kobelco to feel stronger for a few seconds?

Yes. That burst is the power boost function, which temporarily raises the pressure ceiling for breakout, lifting or climbing and then returns to the normal setting. Guangzhou Shenyue Machinery Technology Co., Ltd. supplies the regulators, relief valves and solenoids behind it.

Which parts does the boost function use on an SK200-8?

The K3V112DT main pump with its regulator assembly 29070821-4927, also quoted as YN10V01006F2, plus the main relief valves such as V9510318049-T / LP22V00001F1 / YN22V00004F1 and a boost solenoid in the command path. Fitment must be confirmed against the machine serial.

My machine never boosts any more. Is it the pump?

Rarely. Start with the boost solenoid coil and connector, then measure pressures at the test ports against the manual. A pump that still works normally in every other function is usually not the cause of a lost boost.

Can I turn up the relief valve to get boost back?

No. Relief settings belong to the service manual for the serial and are set with gauges. Over-setting a relief valve makes every function run against the higher pressure, overheating the oil and wearing the pump faster.

Need the parts this article talks about?

Send your part numbers and a photo of the nameplate — real photos and pricing come back with the quote.

Start an Inquiry