A track that comes off is dramatic, but it is almost never sudden. A Kobelco that de-tracks once will do it again, more easily each time, because the chain leaving its rollers is the end point of a list of small faults that were visible for weeks: a track running slack, a flange worn thin, a guard bent out of line. Re-railing without finding the cause turns a maintenance item into a repeat event. Guangzhou Shenyue Machinery Technology Co., Ltd. supplies the undercarriage parts behind most de-tracking causes, and this guide lists them in the order they should be checked. The tension side is covered in our guide to the track tension and recoil spring.
How a chain leaves its rollers
The chain stays on because every component holds it in a straight line: the idler guides the front run, the rollers carry it, the sprocket drives it and the guards catch the moments when forces spike. De-tracking happens when one of those conditions weakens and the chain drifts sideways until it climbs a flange. Slack track gives it the freedom to drift; a worn flange gives it nothing to climb back against; a bent guard or a packed full of mud turns the catch into a lever. Usually one sharp input — a hard turn against a kerb, a side slope, a hook of the track on an obstacle — provides the last push.
The causes, in checking order
Start with tension, because it is free to check and the most common cause: measure sag against the figure in the manual for the serial, and read our tension guide for the method. Then inspect the idler and roller flanges for wear steps and the sprocket teeth for the hooked profile of a worn drive; our guide to sprocket and segment wear covers the drive side, and our link and bushing measurement guide covers the chain itself. Look for bent or missing track guards and for frame damage from previous de-tracking events. Finally, consider the operator file: sustained one-side pivoting, riding over edges and working across slopes all load the chain unevenly, and packing — mud, clay, ice — silently takes up the slack the tensioner thought it had. Ice deserves a special mention in winter: packed snow turns to ice in the gaps overnight, and the machine that tracked perfectly on Friday afternoon throws a shoe-line on the first cold Monday morning.
| Cause | What you find | Fix |
|---|---|---|
| Track too loose | Sag beyond the manual figure | Re-tension to the manual |
| Worn idler or roller flanges | Wear steps, thin flanges | Replace as matched sets |
| Worn sprocket | Hooked, stretched teeth | Replace segments |
| Guard bent or missing | Guards out of line | Re-align or replace |
Parts to inspect and quote
Matched sets matter in undercarriage work, because a new chain on worn rollers wears twice as fast and a new sprocket on a stretched chain does the same. Our stock list carries the SK330-8 track roller 24100N7035F3J1B, also quoted as 24100N7035F3CN, and the idler shaft VA32F2303402, alongside the rollers, idlers and sprocket segments for the smaller classes; the numbering logic is set out in our guide to undercarriage part numbers, and machine-specific listings sit on our SK330 model page. Guangzhou Shenyue Machinery Technology Co., Ltd. quotes undercarriage parts as genuine, OEM or aftermarket at quotation and checks every reference against the serial before it goes out.
Before the machine goes back to work
Re-tension to the manual's figure, not by feel, and note the condition the chain came off in, because a chain that leaves on a hard turn points at different parts than one that walks off in a straight line. Buyers assembling the full set for a serious undercarriage refresh can find the wider range on excavatorpartsglobal.com, our global parts site, and Kobelco's own service documentation sits at kobelco.co.jp. If you are in Shanghai for bauma CHINA 2026, Guangzhou Shenyue Machinery Technology Co., Ltd. exhibits in hall E4, booth 187 — the show floor is a good place to lay a worn sprocket on the table and get an answer in person. Enquiries run through our contact page all year, or directly at the booth.
Frequently Asked Questions
Why does my Kobelco keep throwing its track?
De-tracking repeats because the cause was never fixed. The usual culprits, in order, are slack track, worn idler or roller flanges, a worn sprocket and bent or missing guards. Guangzhou Shenyue Machinery Technology Co., Ltd. recommends measuring sag against the manual before any parts are ordered.
Can I re-rail the track myself?
Yes, gently, with the machine's own movements and never by forcing the chain with the bucket or an attachment. Bent guards and deformed link plates from a forced re-rail turn a short job into a parts order. Find and fix the cause afterwards.
Which undercarriage parts cause de-tracking when worn?
Worn idler and roller flanges let the chain drift and climb, and a hooked sprocket profile feeds the chain unevenly. Our stock list carries parts such as the SK330-8 track roller 24100N7035F3J1B and the idler shaft VA32F2303402, quoted against the machine serial.
Should rollers and idlers be replaced as a set?
Worn parts should be replaced as matched sets per side, because new chain on worn rollers wears at double speed and uneven wear pulls the chain out of line again. Guangzhou Shenyue Machinery Technology Co., Ltd. quotes matched sets and marks every item genuine, OEM or aftermarket at quotation.