Kobelco SK330-8 · Hyd Lines,Swivel · 8 part numbers

Illustration reproduced from the Kobelco SK330-8 parts catalogue for part identification only. Callout numbers on the drawing match the Ref. column in the table below. Kobelco is a trademark of its respective owner; Shenyue Machinery is an independent supplier of excavator parts.
This page lists all 8 part numbers in the Kobelco SK330-8 Hyd Lines,Swivel. The Ref. column mirrors the callout numbers on the illustration, so a part can be ordered straight from the drawing. The list comes straight from the Kobelco SK330-8 catalogue for this machine family.
| Ref. | Part No. | Description | Qty / Assy |
|---|---|---|---|
| LC19H00014F1 | HYD LINES,SWIVEL | ||
| 1 | HH25R08008G3 | CONNECTOR | 1 |
| 1-1 | ZD12P01800 | O-RING | 1 |
| 2 | ZG33F12012 | ELBOW | 3 |
| 2-1 | ZD12P02400 | O-RING | 1 |
| 3 | YN03H01172P1 | ELBOW | 1 |
| 4 | ZD12A01800 | O-RING | 4 |
| 5 | 2444R402D2 | CONNECTOR | 1 |
Kobelco SK330-8 excavator part numbers, taken from the machine's own parts catalogue. Items shared with the closely related SK350LC-8 and the later SK330-9 generation are confirmed from your model plate before quoting.
Read as a dataset, the 8 part numbers spread across 7 number series (ZD12P, LC19H, HH25R being the biggest) The list is weighted toward repeated items such as ring, connector, elbow and 3 seal and O-ring positions.
If you are quoting from this group, start with: ZD12A01800 (o-ring, ×4 per assembly); ZG33F12012 (elbow, ×3 per assembly); HH25R08008G3 (connector, ×1 per assembly). The full list follows below.
For workshops planning a full hydraulic health check, the practical sequence is seals first, then wear items such as valve plates and bushings, and only then complete assemblies. The table below supports that sequence because every level of the breakdown is separately orderable.
Rebuild-at-component-level is the practical route for most Kobelco SK330-8 hydraulic assemblies. Wear shows up at predictable points — spool clearances, valve plates, bearing sets, seal packages — and those items are listed individually, so you can quote only what is worn instead of exchanging the complete unit.
Slow or drifting functions, a circuit that weakens as the oil warms, noise under load, and external leakage at joints are the usual reports. Pressure testing points to the circuit; the drawing callouts then point to the part. The practical first number to ask for in this group is ZD12A01800.
Usually yes — the callout numbers on the drawing map directly to the Ref. column in the table. If your machine differs by serial range, send a photo of the part and we will confirm before quoting.
Yes — send the serial and the part number together; where a position changed across the run we flag it and quote the number that matches your build.
Tank Instal,Hyd
View Parts ListMotor Instal,Swing
View Parts ListHyd Lines,Pump (Suction,Delivery)
View Parts ListHyd Lines,Upp (Main)
View Parts ListFilter List
View Parts ListFrame Assy,Upp
View Parts ListCounterweight Instal
View Parts ListEngine Assy
View Parts ListKobelco SK330-8 workshop guide
Read the guideKobelco SK330-8 workshop guide
Read the guideKobelco workshop guide
Read the guideRepair guides written from our own workshop notes on the Kobelco SK330-8 — the same components listed on this page, with the failure patterns and part numbers we see most often from trade customers.